JVC RX-7012VSL Manuel d'utilisateur télécharger pdf (Page 20)

Storing the Basic Settings and

Adjustments

You can assign and store different sound settings for each different

playing source. By using this function, you do not have to change

the settings every time you change the source. The stored settings

for the newly selected source are automatically recalled.

The following can be stored for each source:

• Bass boost (see page 12)

• Tone adjustment (see page 12)

• Input attenuator mode (see page 12)

• Subwoofer output level (see page 12)

• Balance (see page 13)

• DSP modes

– Surround mode (see page 23)

– DAP mode (see page 25)

• DVD MULTI playback mode (see page 27)

The above settings are stored automatically in the following cases:

• When you turn on the power.

• When you change the source.

• When you assign the source name.

Notes:

• You cannot assign and store different settings for digital input mode

and analog input mode.

• The DSP modes and DVD MULTI playback mode cannot be used at

the same time.

• If the source is FM or AM, you can assign a different setting for

each band.

When playing a software encoded with the DTS Digital

Surround, “AUTO” may not work properly and the following

symptoms may occur:

• Sound does not come out at the beginning of playback.

• Noise comes out while using the searching or skipping

function.

In this case, press CONTROL UP 5/

DOWN ∞ to select “DTS” while “AUTO”

is lit on the display.

• Each time you press the button, the input

mode changes as follows:

Note:

When you turn off the power or select another source, “DTS”

setting is canceled and the digital input mode is automatically

reset to “AUTO.”

To change the input mode back to analog input, select

“ANALOG” by pressing INPUT ANALOG/DIGITAL again.

From the remote control:

1. Press the source selecting

button (DVD, CD, TV/DBS,

or TAPE/CDR)* for which

you want to change the

input mode.

Note:

Among the sources listed above, you can select the digital input

only for the sources which you have selected the digital input

terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)

2. Press ANALOG/DIGITAL to

change the input mode.

• Each time you press the button, the

input mode changes as follows:

When playing a software encoded with the DTS Digital

Surround, “AUTO” may not work properly. In this case, press

CONTROL UP 5/DOWN ∞ on the front panel to select “DTS.”

(See above.)

Note:

You can only select “ANALOG” and “AUTO” using the remote

control.

CONTROL

DOWN UP

DTS

(Digital)

AUTO

(Digital)

DVD MUILTIDVD

TAPE/CDRTV/DBS VCR PHONO

FM/AM

INPUT

ANALOG/DIGITAL

AUTO

(Digital)

ANALOG

Using the Sleep Timer

Using the Sleep Timer, you can fall asleep to music and know the

receiver will turn off by itself rather than play all night.

From the remote control ONLY:

Press SLEEP repeatedly.

The SLEEP indicator lights up on the display,

and the shut-off time changes as follows (in

minutes):

When the shut-off time comes

The receiver turns off automatically.

To check or change the time remaining until the shut-off time

Press SLEEP once.

The remaining time until the shut-off time appears in minutes.

• To change the shut-off time, press SLEEP repeatedly.

To cancel the Sleep Timer

Press SLEEP repeatedly until “SLEEP 00 MIN.” appears on the

display. (The SLEEP indicator goes off.)

• Turning off the power also cancels the Sleep Timer.

2010 30 40 50 60 70 80 90

(Canceled)

SLEEP

EN10_19.RX-7012VSL[A]_f 01.4.25, 1:24 PM17

1 2 ... 15 16 17 18 19 20 21 22 23 24 25 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

JVC RX-7012VSL Manuel d'utilisateur Page 20

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV JVC RX-7012VSL