JVC HR-J245EE Manuel d'utilisateur télécharger pdf (Page 13)

EN 13

Index Search

Your recorder automatically marks

index codes at the beginning of

each recording. This function gives

you quick access to any one of 9

index codes in either direction.

NOTE:

Before starting, make sure the

recorder is in the Stop mode.

ACTIVATE INDEX SEARCH

Press PUSH JOG or (™ or £) on the remote

control. “™ 1” or “£ 1” is displayed on screen

and search begins in the corresponding direction.

● To access index codes 2 through 9, press PUSH JOG

or repeatedly until the correct index number is

displayed.

Ex.: To locate the beginning of B from the current

position, press PUSH JOG twice.

To locate the beginning of D from the current

position, press PUSH JOG once.

● When the specified index code is located, playback

begins automatically.

ﬁ

Current position

AB C D E F

–2 –1 1 2 3

Index number

Next Function Memory

You can set your recorder's power to go off automatically after

the tape is fully rewound. Before starting, make sure the

recorder is in the Stop mode.

For Automatic Power Off After Tape Rewind . . .

. . . press REW, then press within 2 seconds.

NOTE:

If you want the power to be turned off automatically when the

counter reads “0:00:00” (instead of at the beginning of the

tape), press C. MEMORY so that the “M” mark appears before

pressing REW.

Counter Memory

Returns to the counter reading of “0:00:00” to conveniently find

a specific place on the tape automatically.

SET COUNTER MEMORY

Press C. RESET during playback at a point you wish to

locate later. The counter reads “0:00:00”. Then press

C. MEMORY, and “M” appears in front of the counter

digits.

ACTIVATE COUNTER

MEMORY

When you wish to return to the designated point, press

STOP and then REW or FF.

● The tape rewinds or fast-forwards and stops at about

0:00:00 automatically.

● To cancel Counter Memory, press C. MEMORY again.

Instant ReView

Simply by pressing a single button, the recorder power comes

on, rewinds, and begins playback of the last timer-recorded

programme. If you have several programmes recorded, you can

easily access any of them.

NOTE:

Before starting, make sure that the recorder is off and that the

Timer mode is disengaged.

ACTIVATE INSTANT

REVIEW

Press REVIEW. The recorder power comes on and the

recorder searches for the index code indicating the start

of the last timer-recorded programme. Once it’s found,

playback begins automatically.

The front display panel tells you how many programmes

have been recorded. If you have, for example, 3

programmes, “REVIEW” and "3" appear and blink. To

watch the first of the 3 programmes, press REVIEW three

times. The recorder searches and begins playback

automatically. You can access a programme as far as 9

index codes away from the current tape position.

NOTE:

Instant ReView is not possible while the recorder is in the Timer

mode.

£ 2

Tape Position Indicator

The tape position indicator

appears on screen when, from

the Stop mode, you press FF,

REW or perform an Index

Search. The position of “5” in

relation to “0” (beginning) or

“+” (end) shows you where you

are on the tape.

”O.S.D.” (Z pg. 9) must be

set to “ON”, or the indicator

will not appear.

NOTE:

Depending on the type of tape used, there may be times when

the indication is not correct.

1:23:45

+++

Beginning End

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

JVC HR-J245EE Manuel d'utilisateur Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de cassettes JVC HR-J245EE