Jvc SX-L3WD Manuel d'utilisateur télécharger pdf (Page 3)

Connection

Anschluß

Raccordement

Aansluiting

Conexión

Collegamento

Ansluiting

Tilslutning

Liitäntä

连接

Silver

Siber

Argent

Zilver

Plata

Argent

Silverfärg

Sølvfarvede

Hopeanvarinen

银白色

CONNECTION

• Connect the LEFT speaker terminals of the amplifier to the

LEFT terminals of the speaker and RIGHT to RIGHT using

the attached speaker cords as shown in the figure making

sure polarity is correct; (+) to (+) and (–) to (–). Connect the

silver speaker wire to the (–) terminal.

• Turn off power to the whole system before connecting the

speakers to the amplifier.

• The nominal impedance of the SX-L3WD is 6 Ω. Select for

use an amplifier to which a speaker system with the load

impedance of 6 Ω can be connected.

• The maximum power handling capacity of the SX-L3WD is

120 W. Excessive input will result in abnormal noise and

possible damage. In cases where the signals described be-

low are applied to the speakers, even if the signals are be-

low the maximum allowable input, they may cause an over-

load and burn the wiring of the speakers. Be sure to lower

the amplifier volume beforehand.

1) Noise during FM tuning.

2) High level signals containing high frequency components

produced by a tape deck in the fast forward mode.

3) Click noise produced when turning power of other com-

ponents on and off.

4) Click noise produced when connecting or disconnecting

cords with the power on.

5) Click noise produced when the cartridge is replaced with

the power on.

6) Click noise produced when operating amplifier switches.

7) Continuous high frequency oscillation or high pitch elec-

tronically produced musical instrument sound.

8) Howling when using a microphones.

SPECIFICATIONS

Type : 2-way bass-reflex type

Speakers (Magnetically-shielded type)

Woofer : 13.5 cm (5-3/8 in.) cone x 1

Tweeter : 1.9 cm (3/4 in.) dome x 1

Power Handling Capacity : 120 W

Impedance : 6 Ω

Frequency Range : 55 Hz-80 000 Hz

Sound Pressure Level : 87 dB/W·m

Dimensions (W x H x D) : 150 mm x 270 mm x 245 mm

(5-15/16 in. x 10-11/16 in. x 6-11/16 in.)

Mass : 4.5kg (5.6 lbs) each

Accessories : Speaker cord ................... 1

: Spacers ........................... 4

Design and specifications subject to change without notice.

1.Remove the ending part of the vinyl covering from the cut.

2.Twist the wires.

1.Entfernen Sie dan Endstück der Vinylhüle von dem

geschnittenen Teil.

2.Drehen Sie die Kabel.

1.Enlever la pertie d’extrémité du recouvrement vinylique de

la partie déoupée.

2.Tordre les fils.

1.Snijd het laatste gedeelte van de vinylmantel af en verwijder.

2. Draai de draadkernen ineen.

1.Quitar la parte de la extremidad de la cubierta de plástico

de la parte cortada.

2.Torcer los alambres.

Rimuovete l’estremità della copertura in plastica dalla parte tagliata.

2.Torcete i fili.

1. Dra loss den avskurna delen av isoleringen från kabeländen.

2.Tvinna trådarna.

1.Fjern enden af vinyl-isoleringen, hvor den er klippet af.

2.Sno trådene.

1.Irrota muovipeitteen loppupää uurteesta.

2.Kierrä johdot.

1. 从断开处将尾部的塑料套取下来。

2. 拧紧芯线。

Fit the speaker cord into the groove, then

turn the knob clockwise to fasten the cord.

Das Lautsprecherkabel in die Nut einpassen

und dann den Knopf im Uhrzeigersinn

drehen, um das Kabel zu befestigen.

Insérer le cordon d’enceinte dans la

rainure, puis tourner le bouton vers la

droite pour fixer le cordon.

Leg het luidsprekersnoer in de groef en

draai vervolgens de knop met de klok

mee vast.

Fije el cable del altavoz en la ranura, y

después gire el mando hacia la derecha

para fijarlo.

Inserire il filo dell’altoparlante nella

scanalatura e poi girare il pomello in

senso orario per fissarlo e così

assicurare il collegamento.

Passa in varje högtalarkabels kärna i

respektive spår och vrid därefter på

ratten för att dra fast kabeln.

Anbring højttalerkablet i rillen og drej

derefter skruen i retningen mod uret for

at fastgøre kablet.

Sovita kaiutinjohto aukkoon ja kiinnitä

johto sitten paikalleen kääntämällä

nuppia myötäpäivään.

将扬声器导线安设于槽中，然后再按顺

时针方向转动旋钮以固定导线。

ＳＸ－Ｌ３ＷＤ－ＣｓＧ．６５ＣＳ 00.9.7, 1:08 PM3

1 2 3 4 5 6 7 8

Commentaires sur ces manuels

Pas de commentaire

Jvc SX-L3WD Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Microphones Jvc SX-L3WD