JVC RM-P210 Manuel d'utilisateur

INSTRUCTIONSREMOTE CONTROL UNITRM-P210RM-P210 REMOTE CONTROL UNITSC961002-003-HRdFor Customer Use:Enter below the Model No. and Serial No. which are l

10CONNECTIONCAMERA SETUPBefore turning the RM-P210 on, be sure to set up the camera as shown below. GY-DV550 camera KY-D29/KY-D29W cameraSHUTTER STA

11PAINT AUTOBRW.BALAUTOMANUWHITE MASTER BLACKPOWERIOIRISPBAPRESETCLOSE OPENMIDREMOTE CONTROL UNIT RM-P210POWER switch1.Connect the camera to the RM-P2

121.Press and hold the MENU button for about 1 second untilthe LCD display shows the menu display. Turn the con-trol knob to move the cursor () to &qu

13ADJUSTMENTS FOR GENLOCK OPERATIONGenlocking is required for a system, which uses an SEG (special effects generator) as the mainsignal source.REF. :

14The intercom employs the RTS system.If it is required to change this to a 2-wire system, consult yournearest JVC-authorized service agent. (The modi

15FUNCTION KEYSUp to four of the functions listed at the bottom of this page can be assigned to function keys F1 toF4 so that each function can be swi

161.Press the SHUTTER control to activate the shutter speedvariation facility, which is indicated by the lighting of theSHUTTER lamp.2.Turn the SHUTTE

17IRIS ADJUSTMENTThe camera lens iris can be adjusted from the RM-P210.CAMERA ADJUSTMENTS1.When the lamp in the IRIS AUTO/MANU button is not lit,the i

18WHITE BALANCE ADJUSTMENTSince color temperature varies depending on the light source, the white balance should be ad-justed whenever the main light

19FLOW OF MENUSMENU OPERATION1: GENLOCK1A: H PHASE1B: SC COARSE1C: SC FINE0 to 2550°, 90°, 180°, 270°0 to 2551Z: BACK 2: CABLE2A: LENGTH2B: Y CABLE EQ

2 1. Read all of these instructions. 2. Save these instructions for later use. 3. All warnings on the product and in the operating instructions sho

20MENU SETUP METHODEach menu is displayed on the LCD display and can be set up using the MENU button and the control knob.The values set in the "

21GENLOCK MENUMENU OPERATIONThis menu is used to set the camera cable length to the length actually used.( REF. : “Adjustments for Genlock Operation”

22FILE MENUThe values set with the menu and applied to the RM-P210 can be saved in two files named A and B.MENU OPERATION1.Press and hold the MENU but

23PROCESS MENUMENU OPERATIONONNORMALNORMALMIDDLEOFFONNORMALONNo. Item Function, OperationAvailable SettingsInitial Setting4A4B4C4D4E4F4G4HDETAILDETAIL

24PROCESS MENU (CONTINUED)MENU OPERATIONNORMALOFFNORMALNORMAL4:3OFFMIDDLE—No. Item Function, OperationAvailable SettingsInitial Setting4I4J4K4L4M4N4O4

25OPERATION MENUMENU OPERATIONThis menu sets the functions built into the RM-P210.STEP0.1 dB18.0 dB0 dB9 dB18 dBOFFBLACKSTRETCHBLACKCOMPRESSALC+EEILOL

26LCD MODE MENUThis menu sets up the LCD display.NORMALON–No. Item Function, OperationAvailable SettingsInitial Setting6A6B6ZCONTRASTBACKLIGHTBACKAdju

27MENU OPERATIONSYSTEM RESET MENUThis menu resets the values set by the user to the initial values.1.Press and hold the MENU button (approx. 1 second)

28WARNING MESSAGESTo prevent operational errors, the LCD display shows one of the following warning messages whenan erroneous operation is performed.D

29FUNCTIONS AVAILABLE DEPENDING ON CAMERA MODELSGENERALFunctionConnectedModelGY-DV550KY-D29KY-D29WKY-27CKY-19 : Available.  : Not available.

3INTRODUCTIONINTRODUCTIONFeatures... 4Provided Accessories and Documents ...

30TROUBLESHOOTINGGENERALColors in the monitor screen are abnormal. (During genlocking)• Is the SC phase adjusted properly? P. 13Synchronization is n

31SPECIFICATIONSGENERAL Output SignalsComposite video signal:1 V(p-p), 75 W, 2 outputR/G/B signals : 0.7 V(p-p), 75 W, x 1 each (with-out sync)Y/R-Y/

is a registered trademark owned by Victor Company of Japan, Limited. is a registered trademark in Japan, the U.S.A., the U.K. and

4 Do not supply power to the RTS terminals at the rear. Theseterminals are not designed to accept a power supply. To prolong the service life of the

51Intercom jackConnect the intercom headset to this jack.REF. : “Intercom” on page 14.2[INTERCOM LEVEL] controlUse this knob to adjust the intercom ea

6INTRODUCTIONCONTROLS, CONNECTORS AND INDICATORS (CONTINUED)![POWER] switchPress this switch to turn the power ON and OFF.@[WHITE - W.BAL B/A/PRESET]

71[AC ` IN] connectorConnect this socket to a commercial power supply outletusing the power cord provided.2[TALLY] terminalsThese terminals input the

8CONNECTIONEXAMPLE OF BASIC CONNECTION Standard connection of the RM-P210 (Connection of a single unit)HGCCPVWPGMTALLY INTERCOM AUX VIDEO INPUT GENLO

9CONNECTIONEXAMPLE OF RM-P210 (CONNECTION OF 2 UNITS) Standard connection of RM-P210 (Connection of 2 units)MonitorIntercom headset KA-320Camera cabl