JVC VN-C215VP4U Manuel d'utilisateur

For Customer Use:Enter below the Serial No. which is located onthe body.Retain this information for future reference.Model No.Serial No.Thank you for

10IntroductionCamera unitA Mounting hole ⳯ 2Use these when mounting the base to the ceiling, wall or electrical box.(A Pg. 17)(A Pg. 21)Note：

11I Power cable for heater (AC 24 V)(Gray, White)Note： ● When installing a heater (sold separatel

12IntroductionInside the cameraL[10BASE-T/100BASE-TX(PoE)]10BASE-T/100BASE-TX terminalThis is a 10BASE-T/100BASE-TX terminal.It connects to the networ

13S [MONITOR] Monitor terminal (RCA pin)(A Pg. 28)T Heater power connectorThis power connector is used when the camera is installed with a heater (sol

14IntroductionMonitoring Via Built-in ViewerVN-C215VP4U comes with a built-in ActiveX viewer.Monitoring of VN-C215VP4U images using the computer is po

15Restrictions on ClientsIt is possible for VN-C215VP4U to permit or deny image acquisition of designated IP addresses.Control via customized applicat

16SetupThe connection and setup procedures are described as below.KKKProcedures䢇 Make sure you touch the metal surface of the [MONITOR] terminal to re

171.Remove the dome coverLoosen the dome cover fastening screws (x3) with the wrench (supplied) and remove the dome cover.Memo：

18Setup2.Mount the fall-prevention wire to the base(The fall-prevention wire is not attached)Remove the fall-prevention wire mounting screw of the bas

19Fill up the piping hole and mounting hole with sealant, mount the camera to the base and insert silica gel.1.Fill up the holes with sealantUse seala

2IntroductionSafety Precautions1. Read all of these instructions.2. Save these instructions for later use.3. All warnings on the product and in the op

20Setup4.Insert the supplied silica gelTake out the silica gel from its aluminum pack, insert it in the space for silica gel inside the camera and sec

21Mount the base to an electrical box.1.Remove the camera unit from the base(A Pg. 17)2.Mount the base to the electrical boxUse two mounting holes and

22SetupUse a piping hole to mount the camera.Use the piping hole at the bottom of the base to mount the camera1.Remove the camera unit from the base (

23Using the piping hole at the side of the base to mount the cameraWhen the camera is not directly mounted on a ceiling, use the piping hole at the si

24SetupElectricity can be supplied to this product either by using the PoE or connecting to the DC 12 V power supply.䢇 When electricity is supplied to

25Memo： ● In a system where multiple units of VN-C215VP4U are used, turn on the power of only 1 unit

26SetupNote： ● When installing a heater unit (sold separately: KA-ZH215) to this product, be sure

27Connect the alarm input/output cables with external devices such as a sensor, buzzer, etc.Note：

28SetupWhen the camera is mounted, adjust the image settings while looking at the actual image.Mounting the test monitorConnect the [MONITOR] terminal

29Adjusting field angle, focus and brightnessOnce you have decided the shooting direction, you can adjust the field angle, focus and brightness.Note：

3Information for USAThis device complies with part 15 of the FCC Rules.Changes or modifications not approved by JVC couldvoid the user's authorit

30SetupAfter all settings are complete, mount the inner dome to the camera.1.Mount the inner domeMount the inner dome to the claws (x3).Note：

31Note： ● Secure the dome cover tightly. Insecure mounting may increase humidity, fog up the came

32Setting● Ensure that there is sufficient network bandwidth for the data volume to be sent out by VN-C215VP4U.●Data volume to be sent by VN-C215VP4U

33Setting IP address with the default VN-C215VP4U settingsThere are 2 methods to set the IP address when VN-C215VP4U is in its default settings.(A) As

34Setting䢇 IP Address setting at the computerSet the computer to an IP address that enables communication with VN-C215VP4U.1.Click [Start]● Select in

35䢇 Changing the IP address using the Internet Explorer1.Launch the Internet Explorer on the computer2.When proxy setting is enabled in the Internet E

36Setting䢇 Changing the IP address using the Internet Explorer (continued)4.Launch the Internet ExplorerMemo：

376.The top page of VN-C215VP4U appears7.The Basic page with the IP address settings appearsA confirmation screen appears. Press the [OK] button. The

38SettingWhen the IP address of VN-C215VP4U is knownWhen the IP address of VN-C215VP4U is known, it can be changed by using Internet Explorer on the c

39OperationUsing the built-in viewer enables display of a series of images, one-shot recording of images and receiving of alarm information.⽧Setting U

4IntroductionSafety Precautions (continued)Information for Users on Disposal of Old Equipment[European Union]This symbol indicates that the electrical

40OperationSetting Up the Internet Explorer1.Launch the Internet Explorer on the computer2.When proxy setting is enabled in the Internet Explorer, fol

41Setting Up the Internet Explorer (continued)3.If ActiveX controls and plug-ins of the Internet Explorer is not set to AEnableB, follow thesteps belo

42OperationInstalling the built-in viewer1.Enter the URL of the built-in viewer in the address field of Internet ExplorerFor example, if the IP addres

43Screen Configuration of Built-in Viewer● VN-C215VP4U is set to encode at 15 fps by default.ABCDEA Alarm Appears blinking when alarm packets are sent

44OperationQuitting the Built-in ViewerTo quit, press the [Close] button at the top right of the window.● To restart the built-in viewer, launch the I

45OthersCamera Unit[Monitor Output]Monitor output x 1 (75 , 1 Vp-p)[Network Output]LAN SpecificationsCompliant with IEEE802.3, IEEE802.3u and IEEE802.

46OthersGeneralAttachments/AccessoriesStart-up Guide ... 1CD-ROM...

47Dimension [Unit: mm (inch)]T Specifications and appearance of this unit and related products are subject to change for product improvement without p

© 2006 Victor Company of Japan, LimitedLST0530-001AVN-C215VP4UFIXED IP DOME CAMERAVN-C215VP_EN.book Page 48 Wednesday, December 20, 2006 4:26 PM

5䢇 The unit is to be powered by a DC 12 V power supply.䢇 The unit is to be powered by a UL Listed DC12 V power supply. (For U type)䢇 The 12 V DC power

6Introduction䡵 High anti-dust and waterproof performanceThe anti-dust and waterproof mechanism allows outdoor installation as the camera is not affect

7IntroductionSafety Precautions ... 2Main Features ... 6Contents ...

8Introduction䡵 PC Specification Requirements䡵 LAN Environment● 10BASE-T/100BASE-TX(PoE) network interconnected using an IEEE802.3-compliant switching

9Others䢇 This product has a built-in AGC circuit. When AGC is AOnB, the product sensitivity increases automatically at dark places and the image on th